The 3D Field Engine turns a construction drawing set into a 3D model you can walk through on a phone or a computer. It builds the walls, doors and rooms from the plan, reads ducts, diffusers, grilles, HVAC units and piping off the mechanical sheets, and shows electrical and plumbing as layers you switch on and off. Walk at eye height, walk through walls, measure anything, and open the conflicts it found in the drawings before you bid or build.
Verified against the engine's runs on our own sample set and on public tender drawing sets
- 1Supply duct, read off the mechanical sheet with its size, running to the diffusers in the ceiling.
- 2Electrical panel and the conduit along the deck, dropping to each outlet.
- 3Hot and cold water to the washroom sink.
- 4The drain under the slab. Take the floor away to see it.
- 5A conflict. This wall is written one length and drawn shorter, so the door scheduled for its opening no longer fits. The engine flags it Too short.
What can you do in the model?
Stand at eye height and walk the rooms. On a phone, a thumb pad moves you and you look around by moving the phone; on a computer, the keyboard and the mouse. Walls stop you, the way they will on site.
One button and the walls let you pass, to get to the room behind or the ceiling space above without walking around.
Walls, floors, ceilings, HVAC, electrical and plumbing are each a layer. Switch one off, or ask in plain words: "show me the ducts", "hide the walls".
A tape measure that hooks onto wall corners and faces and squares itself up. The length shows in feet and inches and stays on the model.
Every room with its size, floor area, wall area less the doors, ceiling and floor finish, and a total. Copy it straight into a spreadsheet.
Door widths, washroom turning circles and corridor widths, measured on the model and held against common Ontario numbers. They inform; your code consultant decides against the Ontario Building Code.
The grind
- Reading a two-dimensional set and picturing the building in your head
- Ducts, pipes and wiring on separate sheets that nobody lays over each other
- A clash found on site, after the material is ordered and the crew is there
- Walking a client or a sub through a building that only exists on paper
- Dimensions that do not agree from one sheet to the next
How does it catch drawing conflicts?
It measures the drawings against themselves. Every written dimension on the plans is measured between its ticks at the sheet's scale. It flags a dimension written one length and drawn another, millimetres that disagree with feet, a string of pieces that does not add up to its overall, a room number given two names, and door tags that do not match the schedule. When a wall comes out shorter than written, it says which room changes, which walls move, and whether the door or fixture drawn in that stretch still fits. If it no longer fits, it says Too short, in red, first on the list.
Each conflict is a red marker on the model: pick it and the model flies there. Then the drawing check turns them into a list of questions for the architect, already worded, with a sharp close-up of the spot on the sheet. Keep or skip each one, edit the words, then copy, email or print the list.
It only calls what it is sure of. On the five drawing sets we have audited it raised four real problems and no false ones, and errors we planted in a copy of a set were caught. A clash caught on the drawings costs an email. The same clash caught on site costs a day.
Why walk a building that is not built yet?
- Bid with the building in front of you. See the ceiling space the ducts need before you price the bulkheads.
- Coordinate the trades. Ducts, pipes and conduit in one model instead of three sheets nobody lays over each other.
- Walk the client through it. On your phone, in their office, before the first stud goes up.
- Brief the crew. Show the site super where the drain runs before the slab is cut.
- Settle a question on site. Measure the room on the model while you stand in the real one.
What we build
Built from the drawing's own lines and CAD layers, at its scale, with the rooms named where the drawing puts them.
Supply, return and exhaust ducts, diffusers, grilles and units, heating, chilled water and condensate piping, each with the size and tag the sheet gives it.
Panels, conduit, outlets and lights; cold, hot, drain and vent. Pipes drawn on the plumbing sheets are read; the rest is placed by rule of thumb and labelled so.
Every conflict the drawing check finds is a red marker you can fly to, with the question for the architect already worded.
The same model on a phone or a computer, from a link inside your app. Walk it, measure it, show it.
No second upload. The set you price is the set you walk.
What does the 3D Field Engine cost?
A low-cost extra on top of the Takeoff Engine, priced to your work. Taken on its own, it is $150 a month added to your app, like every engine, on top of your app's own monthly plan, and adjusted to the scope of your work in writing before anything is signed.
There is no buy button: email info@bluecraneworks.ca and we set it up with you. The Takeoff Engine's price and the app's own plan on the pricing page are the rest of the bill. CAD, plus HST.
What is read from the drawings, and what is placed?
We label the difference, because a model that looks finished is not the same as one that was read.
| Part of the model | Where it comes from | Good for |
|---|---|---|
| Walls, doors and rooms | Read from the architectural plan | Their lengths, openings and areas |
| Ducts, diffusers, grilles, units and piping | Read from mechanical sheets drawn with CAD layers or clear linework | The sizes and tags the sheets give them |
| Plumbing pipes on plumbing sheets | Read, and they replace the estimated runs | What the sheets show |
| Electrical and plumbing with no engineer's sheets | Placed by rule of thumb | A guide to the scale of the job, not a quantity to order from |
| Heights the plan does not give | Assumed | Shown on the model, for you to confirm |
Can it be added to the app I already have?
Yes. It goes on top of the Takeoff Engine as a low-cost extra, or on its own at $150 a month, into any app we built for you. Jackman Mechanical's app carries it today. Everything we make can be added to a Nameplate app, so your company's app grows as you ask for more, under your own name.
Email us to add itWrite to info@bluecraneworks.ca with what you build and, if you can, a drawing set you would like us to run. Want to see it first? You can request a takeoff demo.
Is the model on a public page?
No. The model and the drawings it comes from live inside your own app, behind your sign-in. The cutaway above is a made-up job drawn for this page.
What it replaces
- Picturing the building from flat sheets
- Laying the mechanical sheet over the plan by hand
- Finding the clash on site
- A rendering you pay for once and cannot walk
Who it is for
General contractors, project managers, estimators and site supervisors in Ontario working from drawing sets, and the clients they walk through a building before it is built.
What week one looks like
- We run one of your drawing sets through the engine with you.
- You walk it on your phone, switch the layers and open the conflicts it found.
- We hold the conflicts against what you already knew about that set.
- It goes into your app, or runs beside the Takeoff Engine on its own.